Skip to main content
Fence Planner

Chain-Link Fence Calculator

Work out the chain-link quantities that follow directly from your measurements: fabric footage and rolls, top-rail pieces, and line, terminal and gate posts. Fittings are left for your supplier, because they depend on the system you buy.

Planning estimate only. Results come from the measurements and prices you enter. They are not an engineered design, code or permit advice, or a quote. See how every number is calculated.

Straight 100 ft fence

Loading saved draft…

Chain-link settings

Maximum post spacing

The longest bay you will allow, post centre to centre. Each run is divided into equal bays no longer than this. The starting value is illustrative, not a code or manufacturer requirement.

Chain-link options

Starting values are illustrative. Enter the roll and rail sizes your supplier actually sells.

%

Added to the solid fence footage to get the fabric order length.

Fabric roll length

On: the theoretical minimum number of rolls. Off: rolls are counted span by span, which can overcount.

Top-rail piece length

Top-rail overlap at each joint

Length lost where one piece sleeves into the next. Must be shorter than a rail piece.

Fence runs

  1. Run 1 (point A to point B)

    Run 1 length

Add a run

Starting from an existing point shares one post there (a corner).

New run length

Direction of travel on the diagram, away from the start point.

Points and connections (exact coordinates, closing a shape, tees)

Coordinates are in feet from the first point (x to the right, y up). Moving a point changes only the runs that end there.

Point A
ft

Negative values are allowed.

ft

Negative values are allowed.

Point B
ft

Negative values are allowed.

ft

Negative values are allowed.

Connect two points with a new run

Add a connection point along a run

Use this to attach another run part-way along a fence (a tee). Lines that merely cross are never joined automatically.

Distance from the run’s start

Gates (0)

How gates are measured here: the opening is the distance between the centres of the two gate posts. That is not the same as a gate’s nominal leaf width or the clear passage between posts. Check the hinge, latch and post allowances in your gate manufacturer’s instructions before setting posts.

No gates yet. A fence without gates is fine – skip this step, or add a gate below.

Add a gate

New gate opening

Gate-post centre to centre.

New gate distance from the run’s start

To the centre of the first gate post.

This tool works on the same project as the other calculators on this site, so the layout you enter here is the one used everywhere.

Layout

Top-down fence layout diagram1 run, 100 ft of fence line: 100 ft solid fence and 0 in of gate openings. 14 posts in total: 2 end, 12 line. Shared corners are counted once.
  • End post
  • Corner post
  • Gate post
  • Line post
  • Junction (review) post
  • Fence
  • Gate opening

Not to survey accuracy. Letters mark layout points; small numbers are post numbers from the post schedule; grid lines are 10 ft apart.

Layout described in words
  • 1 run, 100 ft of fence line: 100 ft solid fence and 0 in of gate openings.
  • 14 posts in total: 2 end, 12 line. Shared corners are counted once.
  • Run 1 goes from point A to point B, 100 ft, heading right (→).

Chain-link material takeoff

Your project’s fence type is Wood. The quantities below show what the same layout would need in chain-link. To use chain-link in the cost estimate, switch the project.

Chain-link quantities
ItemQuantityBasis
Fabric, net100 ftSolid fence only – gate openings excluded
Fabric to order105 ftNet + 5% waste allowance
Fabric rolls350 ft rolls; theoretical minimum, assumes off-cuts are spliced
Top rail, net100 ftEquals solid fence footage
Top-rail pieces1010 ft 6 in pieces, 6 in overlap; rounded up per span
Line posts12Intermediate posts from the spacing rule
Terminal posts22 end, 0 corner, 0 gate
By uninterrupted span (terminal post to terminal post)
SpanLengthTop-rail pieces
Span 1 (run 1)100 ft10

Not calculated – confirm with your supplier or installer

  • Tension bars, tension bands and brace bands Needs installer confirmationQuantities depend on fence height and the number and type of terminal posts.
  • Rail ends, loop caps, post caps and tie wires Needs installer confirmationVaries by supplier system; not calculated here.
  • Bracing, tension wire and gate hardware Needs installer confirmationDepends on height, terrain, gate type and local practice.

What this chain-link calculator gives you

A chain-link fence is bought as separate parts – fabric by the roll, top rail by the piece, two kinds of post, and a bag of fittings. The first three follow from geometry, so they can be calculated from a measured layout. The fittings do not: the number of tension bands on a terminal post, for instance, depends on the fence height and the supplier’s system. This calculator does the geometry and is explicit about where it stops.

Calculated from your layoutLeft for your supplier or installer
Fabric footage, with your waste allowanceTension bars, tension bands, brace bands
Number of fabric rollsRail ends, loop caps, post caps, tie wires
Top-rail footage and stock piecesBracing, tension wire, bottom rail
Line posts and terminal posts (end, corner, gate)Gate frames, hinges and latches
Concrete, from your hole sizePost diameter, wall thickness and footing size

How each quantity is calculated

Fabric

net fabric   = solid fence footage           (gate openings excluded)
order length = net fabric × (1 + waste %)
rolls        = order length ÷ roll length, rounded up

That roll count is a theoretical minimum: it assumes the off-cut from one stretch can be spliced into the next. If you would rather not splice, switch splicing off. Rolls are then counted separately for every span between terminal posts, which is safer but can overstate what you need – the calculator says so when it does this.

Top rail

Top rail runs continuously over the line posts but stops at every terminal post, so pieces are worked out one uninterrupted span at a time. Where two pieces join, one sleeves into the other and that overlap is lost:

pieces for one span = (span − overlap) ÷ (piece length − overlap), rounded up
                      (never fewer than 1)

Off-cuts are not carried from one span to another. This is a purchasing approximation, not a cutting plan.

Posts

Terminal posts are the end, corner and gate posts – the ones the fabric is tensioned against. Line posts are the intermediate posts placed by the spacing rule. A corner shared by two runs is one terminal post. A point where three or more runs meet is counted once and flagged for review, since how it is built is an installer’s call.

Worked example

A straight 100 ft line with a gate whose posts are 4 ft apart, starting 38 ft from one end. Maximum post spacing 8 ft, 50 ft rolls, 5% fabric waste, 10 ft 6 in rail pieces with a 6 in overlap.

  • Solid fence: 38 ft + 58 ft = 96 ft. The 4 ft gate opening takes no fabric or rail.
  • Fabric to order: 96 × 1.05 = 100.8 ft, so 3 rolls of 50 ft.
  • Top rail: the 38 ft span needs (38 − 0.5) ÷ (10.5 − 0.5) = 3.75, so 4 pieces; the 58 ft span needs 57.5 ÷ 10 = 5.75, so 6 pieces. 10 pieces in all.
  • Posts: 2 end + 2 gate = 4 terminal posts, and 4 + 7 = 11 line posts. 15 posts in total.

Load the “Run with a gate” example in the fence cost calculator to see these numbers produced live, then change them to your own.

What you need to enter

  • Each straight run’s length, and where runs meet.
  • Each gate’s position and the centre-to-centre distance between its posts.
  • The maximum distance you will allow between posts.
  • The roll length and top-rail piece length your supplier sells, and the rail overlap at a joint.
  • A fabric waste allowance you are comfortable with.

Assumptions and limits

  • Post spacing is not prescribed here. Maximum line-post spacings are set by the fence product, the supplier’s system and local requirements, and they differ. There is no single universal figure. Enter the spacing your supplier or installer specifies.
  • Roll and rail sizes shown at the start are placeholders. Sizes vary between suppliers.
  • Fence height is recorded for your supplier but does not change these quantities; it does change the fittings, which is why they are not calculated.
  • Ground is treated as flat. On a slope, fabric and rail lengths follow the slope and will be longer.
  • Gates are separate items. Their frames, fabric and hardware are not part of the fence fabric total.

Common mistakes

  • Ordering fabric for the gate opening. The gate has its own fabric; the fence fabric stops at the gate posts.
  • Buying line posts for the ends and corners. Terminal posts are a different, heavier item. Count the two kinds separately.
  • Dividing total rail footage by the piece length. Rail stops at every terminal post and loses length at every joint, so short spans waste more than the simple division suggests.
  • Assuming a fittings list from another job. A taller fence or a different supplier’s system changes the counts.

References

Every calculator works on the same saved project, so you can move between them without re-entering your layout.